A home accessibility ramp may look like a straightforward project, but there is much more to it than laying several boards over the front steps.
The ramp needs to work for the person using it. It also needs a dependable structure, practical slope, adequate landings, safe transitions, usable handrails, drainage, and enough room to approach and operate the door.
Those details become even more important during a Maryland winter, when rain, leaves, frost, snow, and ice can make an inconvenient entrance unsafe.
When I evaluate a property for a residential accessibility ramp, I start with the person’s needs and then work outward to the door, route, yard, structure, and permit requirements.
Start with the person who will use the ramp
Two people can use the same mobility device but need very different ramp designs.
Before deciding where a ramp should go, I want to understand:
- Is the person using a manual wheelchair, power wheelchair, scooter, walker, cane, or another device?
- Will the person travel independently or with help?
- Is a caregiver pushing the chair?
- How much turning space does the mobility device require?
- Is balance a concern?
- Is grip strength limited?
- Does the person need access from a particular vehicle?
- Will equipment, oxygen, groceries, or medical supplies travel with them?
- Is the need expected to be temporary or long-term?
- Could mobility needs change in the future?
A ramp that technically reaches the door may still be exhausting, difficult to turn on, or poorly aligned with the person’s usual route.
When a healthcare professional or occupational therapist has provided recommendations, those should be considered during the design.
Measure the total rise—not just the number of steps
The starting point for ramp planning is the total vertical rise from the walking surface at the bottom to the finished entrance level.
That measurement can include:
- The height of the steps
- The porch or landing height
- The door threshold
- Changes in the surrounding grade
- A transition from the driveway or walkway
- Drainage slope
The rise affects the required ramp length.
As a familiar planning reference, the federal ADA Accessibility Standards generally use a maximum running slope of 1:12 for covered ramps. That means one foot of ramp run for each inch of vertical rise. A 24-inch rise would therefore require approximately 24 feet of sloped run before adding the required landings. [Source]
That example explains why a safe ramp can occupy more space than homeowners initially expect.
However, the ADA Standards do not automatically govern every private single-family residence. The applicable residential code, permit requirements, project funding, property use, and local jurisdiction must be confirmed.
I use the person’s needs and the project’s actual requirements to determine the design—not a shortcut copied from a generic ramp diagram.
A gentler ramp is usually easier to use
The steepest permissible slope is not always the best slope.
A gentler ramp may be easier for:
- Someone propelling a manual wheelchair
- A caregiver pushing another person
- A person using a walker
- Someone with limited strength or endurance
- A person who has difficulty controlling a wheelchair on a descent
- Anyone using the ramp in wet or cold weather
The U.S. Access Board recommends providing the least possible slope below the 1:12 maximum where practical because gentler slopes improve usability for a wider range of people. [Source]
The tradeoff is space.
A gentler slope requires a longer ramp or additional turns. That can affect the yard, walkway, driveway, landscaping, and project cost.
Choose the entrance before designing the ramp
The front door is not automatically the best accessible entrance.
Depending on the property, a side, rear, or garage entrance may provide:
- Less vertical rise
- A shorter route
- Better protection from weather
- More room for landings
- Easier vehicle access
- Better lighting
- A more private entrance
- Less impact on the front yard
I also look at where the route ends.
The bottom of the ramp should connect to a stable and usable surface—not mud, loose gravel, an uneven yard, or a location where the wheelchair user must enter vehicle traffic.
Questions I consider include:
- Where does the person park?
- Can a vehicle door or lift open safely?
- Is the route from the vehicle level and firm?
- Will the ramp block another entrance?
- Does the route cross a driveway?
- Is there room for a wheelchair to turn?
- Will a gate interfere with access?
- Can emergency responders reach the entrance?
- Where will snow be piled?
The shortest ramp is not necessarily the most useful ramp if it ends in the wrong place.
Landings are part of the ramp
A landing is not leftover space between two sloped sections. It is a working area where the user may need to stop, turn, open a door, or change direction.
Landings are generally needed:
- At the top
- At the bottom
- Between ramp runs
- Where the ramp changes direction
- At doors
- Where required by the applicable design
Under the ADA Standards, landings are required at the top and bottom of ramp runs. Landings at directional changes generally need sufficient clear space for maneuvering, and the Access Board illustrates 60-inch-by-60-inch intermediate landings where a ramp changes direction. [Source]
Again, those federal dimensions should not be assumed to be the only requirements for a private residence. They are useful planning references that show why a tiny platform at a switchback can be difficult to use.
Posts, railings, door swings, and other components should not take away the clear space the user needs.
Door operation can determine whether the ramp works
Reaching the entrance is only part of the job. The user must also be able to open and pass through the door.
I evaluate:
- Which direction the door swings
- Whether the user must pull or push it
- Space beside the latch
- Storm-door operation
- Threshold height
- Door width
- The location of the handle and lock
- Whether the door closes too quickly
- Whether someone can remain on a level surface while operating it
- Whether a screen or storm door creates an additional obstacle
A wheelchair user should not have to stop on the sloped ramp, hold position, pull a door backward, and then maneuver around it.
The U.S. Access Board advises locating door swings outside ramp landings when practical because it can improve safety and maneuverability. [Source]
Sometimes the entrance itself needs modification in addition to the ramp.
The threshold needs a smooth transition
A tall lip at the doorway can defeat the purpose of the ramp.
Small front casters on a wheelchair can catch at abrupt transitions. Walkers can also become difficult to lift over a threshold.
Possible improvements may include:
- A properly designed threshold transition
- Adjusting the exterior landing height
- Replacing an unsuitable threshold
- Modifying the door
- Installing a compatible threshold ramp
- Improving weather sealing without creating an obstacle
The solution needs to keep water out of the house while providing a practical transition.
Simply building the landing level with the interior floor can create water-management problems if the doorway and flashing were not designed for it.
Width should account for real use
The ramp needs enough clear width for the mobility device, the user, and any caregiver assistance.
The Access Board’s ADA guide identifies a 36-inch minimum clear width between handrails for covered ramps. [Source]
A residential project may benefit from more space depending on:
- Wheelchair width
- Hand position
- Caregiver assistance
- Medical equipment
- Turning movements
- The entrance door
- Rail and post placement
- Future mobility needs
The important measurement is the usable clear width after handrails and other obstructions are installed—not merely the outside width of the framing.
Handrails must be usable
A decorative top rail is not always a graspable handrail.
A dependable handrail should be:
- Continuous where required
- Securely connected
- Comfortable to grip
- Free of sharp or abrasive edges
- Positioned consistently
- Clear of posts and other obstructions
- Properly terminated
- Able to support the intended use
The ADA guide calls for handrails on both sides of covered ramps with a rise greater than six inches and describes gripping surfaces, clearances, continuity, and extensions. [Source]
The exact residential requirement must still be confirmed for the project.
Someone who relies on a handrail for balance should not discover that the rail stops before the transition, is too large to grip, or moves under pressure.
Guards and edge protection serve different purposes
Handrails help a person maintain balance and control. Guards help protect against falling from an elevated edge. Edge protection helps keep wheelchair casters, walker tips, and crutches from slipping off the ramp surface.
A particular ramp may need more than one of these features.
The Access Board explains that ramp-edge protection can be provided through curbs, barriers, rails, or extended surfaces, depending on the design. [Source]
I look at:
- Ramp height above grade
- Open sides
- Railing openings
- Wheel and caster position
- Drainage gaps
- Children or pets using the area
- Transitions at landings
- The relationship between ramps and adjacent stairs
A low curb should not be mistaken for a guard where a guard is required.
The surface needs dependable traction
Outdoor ramp surfaces are exposed to:
- Rain
- Dew
- Frost
- Snow
- Ice
- Leaves
- Algae
- Dirt
- De-icing products
- Wheel and foot traffic
The surface should be firm, stable, and slip-resistant.
Material choices may include pressure-treated wood, composite decking, aluminum systems, or other approved surfaces. Each has tradeoffs.
Pressure-treated wood
Wood can be practical and adaptable for a custom residential layout. It still requires appropriate framing, fastening, spacing, maintenance, and attention to surface traction.
Boards may move as moisture conditions change. A worn or algae-covered wood ramp can also become slippery.
Composite decking
Composite products can reduce some maintenance associated with wood, but they are not automatically slip-proof.
The selected product must be approved for the intended application and installed according to its requirements for joist spacing, fastening, ventilation, and temperature-related movement.
Aluminum ramp systems
Modular aluminum systems can be useful for temporary needs, properties where future relocation is likely, or situations where rapid installation is important.
They still need proper support, transitions, landings, handrails, and a stable base.
Material should be chosen around the user and property—not appearance alone.
Drainage becomes critical during winter
A safe ramp should not direct water toward the house or allow it to collect on landings.
The Access Board’s guide states that landings exposed to wet conditions should be designed to prevent water accumulation. [Source]
I look for:
- Roof runoff
- Gutters and downspouts
- Low areas
- Splashback
- Water coming from the driveway
- Snowmelt
- Ice forming at the bottom transition
- Leaves blocking drainage
- Shaded areas that remain wet
- Soil erosion near supports
A ramp beneath an unprotected roof edge may receive a concentrated sheet of water exactly where the user needs to stop and open the door.
Sometimes the surrounding drainage or gutter layout needs to be addressed along with the ramp.
Snow removal needs to be part of the plan
A ramp takes longer to clear than a short set of steps.
Before building, homeowners should consider:
- Who will remove snow?
- Can a shovel move around the railings?
- Where will cleared snow be placed?
- Will meltwater run back onto the ramp?
- Can de-icing products be used with the selected materials?
- Does the entrance receive morning or afternoon sun?
- Is there a protected alternative entrance during severe weather?
A ramp that is safe in October can become difficult to use after a few inches of snow if maintenance was not considered.
Lighting is also important because winter use often occurs before sunrise or after sunset.
The ramp still needs a dependable structure
An accessibility ramp is a walking surface supported by a structural system.
Depending on the design, I evaluate:
- Footings
- Posts
- Beams
- Joists
- Ledgers or other house connections
- Blocking
- Structural connectors
- Railing-post reinforcement
- Fasteners
- Landings
- Stair connections
- Bearing points
- Soil and drainage
The structure should provide a clear load path into the ground.
Setting posts without considering frost, drainage, soil, or lateral movement can create a ramp that shifts over time. Attaching the ramp to deteriorated porch framing can transfer the problem into the new work.
The existing porch, stoop, deck, or entrance should be evaluated before the ramp is connected to it.
Permanent and temporary ramps solve different problems
A person recovering from surgery may need access for several weeks. Someone planning to remain in the home may need a permanent structure designed for daily use.
A temporary or portable ramp may be appropriate when:
- The need is short-term
- The rise is limited
- The equipment is approved for the application
- A permanent structure is not yet possible
- The entrance and landing can safely support it
A permanent ramp may make more sense when:
- The ramp will be used daily
- The rise requires multiple runs
- Weather exposure is significant
- A custom route is necessary
- Long-term durability matters
- The user’s mobility needs may continue or change
Maryland’s statewide equipment resources include a portable-ramp loan program for qualifying short-term needs, with ramps typically loaned for up to 120 days. [Source]
A portable ramp should not be used as an improvised replacement for a properly designed permanent ramp when the height, landing, or site requires more substantial construction.
Permits and plans should be addressed early
Permit requirements depend on the ramp, property, jurisdiction, and scope.
Frederick County’s published expedited residential-permit guidance lists accessibility ramps among the projects that may qualify for its expedited process. Final eligibility still depends on the project and county review. [Source]
Frederick County also explains that building permits establish minimum safety requirements for new construction and modifications to existing structures. Properties within municipalities may need zoning approval before the county building-permit application. [Source]
Washington County provides its permit applications, plan requirements, codes, zoning information, online permitting, and inspections through its Division of Permits and Inspections. The exact requirements should be confirmed for the property. [Source]
For Darling Builders projects:
- I explain when a permit is required.
- When a permit is required for our contracted work, I handle pulling it unless the agreement states otherwise.
- The homeowner supplies HOA documents and obtains HOA approval.
- I help complete the construction-related portions of an HOA submission.
- Darling Builders contacts Miss Utility when our work requires excavation.
- The homeowner identifies private underground systems that public utility locating may not mark.
- The homeowner confirms the property line unless surveying is separately included.
Permit approval, HOA approval, and medical recommendations are separate matters. One does not automatically satisfy the others.
Financial-assistance resources may be available
I do not promise that a homeowner will qualify for financial assistance, but Maryland maintains several resources worth reviewing before work begins.
The Maryland Department of Disabilities identifies ramps as a common home modification and lists potential assistance through the Maryland Assistive Technology Loan Program and Accessible Homes for Seniors. [Source]
Maryland’s Accessible Homes for Seniors program may provide loans or grants to eligible seniors for improvements including ramps, accessible showers, grab bars, and lever handles. [Source]
Maryland also maintains an Independent Living Tax Credit for qualifying accessibility renovations. Eligibility, documentation, funding, and deadlines should be confirmed directly with the administering agency before relying on assistance. [Source]
Some programs require approval before construction begins, so it is better to investigate them during planning rather than after the ramp is finished.
What affects the cost of an accessibility ramp?
The total rise is one of the largest factors because it determines the approximate amount of ramp and landing area required.
Other factors include:
- Number of ramp runs
- Number and size of landings
- Direction changes
- Material selection
- Handrails and guards
- Footings and support structure
- Existing porch condition
- Door or threshold modifications
- Demolition
- Sidewalk or landing work
- Drainage
- Lighting or electrical work
- Property access
- Permit and plan requirements
- Landscaping
- Winter working conditions
A ramp with a lower rise may still require careful work if the door, walkway, drainage, or available space creates a difficult layout.
I need to evaluate the property before recommending a final design or price.
What to send when requesting an estimate
The following information helps me prepare:
- Wide photographs of the entrance and yard
- Pictures of the steps and door
- Approximate height from the ground to the entrance
- Photos of the driveway or parking location
- The mobility device being used
- Whether the person travels independently or with assistance
- The preferred entrance
- Available property plat or survey
- HOA requirements
- Known private utilities or drainage systems
- Whether the need is temporary or long-term
- The desired timeframe
- Any recommendations provided by an occupational therapist or healthcare professional
Medical details do not need to be shared beyond what is necessary to understand the person’s practical access needs.
Need a safer way into your home before winter? Request an on-site estimate, and I’ll evaluate the entrance, rise, route, landings, drainage, structure, and permit considerations for a practical accessibility-ramp design.
My bottom line
A dependable home accessibility ramp starts with the person using it.
Slope matters, but so do the landings, door swing, threshold, handrails, edge protection, surface traction, lighting, drainage, and route to the vehicle.
The ramp also needs to be structurally supported and designed for the property rather than copied from a one-size-fits-all plan.
I would rather spend time planning a ramp that is comfortable and useful than build the shortest structure that can physically reach the door.
Darling Builders provides accessibility-ramp and outdoor-construction estimates throughout Washington County and Frederick County, Maryland.
Common questions
Frequently asked questions
Does a wheelchair ramp at a private home have to meet ADA requirements?
Not every private single-family residence is automatically governed by the federal ADA Standards. Local residential code, permit requirements, funding programs, property use, and the user’s needs may determine the applicable design. ADA dimensions remain a useful planning reference.
How long does a residential wheelchair ramp need to be?
The length depends primarily on the total vertical rise and selected slope. Using a 1:12 planning reference, each inch of rise requires approximately one foot of ramp run, not including landings. The final design must follow the project’s applicable requirements.
Does a home accessibility ramp require a permit?
It may. Requirements depend on the structure, property, and jurisdiction. Frederick County processes residential accessibility-ramp permits, and Washington County requirements should be confirmed through its Division of Permits and Inspections.
What is the best material for an outdoor accessibility ramp?
There is no single best material for every home. Pressure-treated wood, compatible composite decking, and modular aluminum systems each have advantages. The choice should consider duration, maintenance, traction, structure, weather exposure, and the user’s needs.
Does a residential ramp need handrails on both sides?
That depends on the rise, design, applicable code, and user. The ADA Standards require handrails on both sides of covered ramps with a rise greater than six inches, but the exact private-residential requirement should be confirmed for the project.
Can an accessibility ramp be built over existing steps?
Sometimes the ramp can be designed around, beside, or over part of the existing entrance. The steps, landing, door, supports, drainage, and required clearances must be evaluated before deciding what can remain.
Can I use a portable ramp instead of building a permanent one?
A properly selected portable ramp may work for a short-term need or limited rise. It should not be used where the height, landing, transition, weather exposure, or daily use requires a permanent structure.
What makes an accessibility ramp safer during winter?
A practical slope, slip-resistant surface, secure handrails, edge protection, drainage, lighting, protected landings, and a realistic snow-and-ice removal plan all contribute to safer winter use.
Plan your project
Let’s look at your property.
Darling Builders provides free on-site estimates throughout Washington and Frederick Counties, Maryland. We’ll discuss your goals, site conditions, materials, and the work your project requires.

